uri:annex/ii/appendix/1/division/1/division/3/division/3.1/division/3.1.3.2
- Ensure service brake demand value is 650–850 kPa for vehicles with electric control lines
Retained EU Law
2015
United Kingdom
Commission Delegated Regulation (EU) 2015/68 of 15 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle braking requirements for the approval of agricultural and forestry vehicles (Text with EEA relevance)
At a glance
What's here
16 compliance obligations
What this Act requires
Sections that create concrete duties on businesses or carry penalties. Procedural and definitional sections are folded into the “Browse other sections” expander at the bottom of each group. Click any section title to read the source text on legislation.gov.uk.
uri:annex/iii/division/6
- Manufacturer must specify test pressure for spring brake response time
uri:annex/iv/division/a/division/3
- Fit pressure test connections to the least efficient air reservoir
uri:annex/iv/division/b/division/1/division/1.2
- Ensure brake reservoirs hold enough vacuum for secondary braking
uri:annex/v/division/2
- Ensure spring braking systems meet design, performance and testing requirements
uri:annex/viii/division/6/division/6.1
- Submit detailed brake drawings and test data to the Technical Service
uri:annex/viii/division/6/division/6.2
- Test brakes with appropriate forces depending on overload protector
uri:annex/xi/appendix/4/division/1
- Provide test surface adhesion data and test results to the technical service
uri:annex/xi/division/5/division/5.1/division/5.1.1
- Ensure braking system meets type-approval performance standards
uri:annex/xii/division/4/division/4.1
- Provide failure analysis of control transmission to Technical Service
uri:annex/xii/division/4/division/4.2
- Provide failure analysis of electric control transmission to Technical Service
uri:annex/xii/division/5/division/5.1/division/5.1.1
- Ensure service braking activates stop lamps on agricultural/forestry vehicles
uri:annex/xii/division/5/division/5.2/division/5.2.3
- Activate yellow warning signal on low voltage in towed vehicles
uri:annex/xii/division/5/division/5.2/division/5.2.5
- Ensure towed vehicle braking system stops lamp signals comply at type approval
Fitting and demonstration requirements related to braking performance
- Design, build and test braking systems to ensure they meet EU technical standards
Requirements applying to hydraulic connections of the single-line type and to tractors fitted with them
- Stop fitting single-line hydraulic braking connections to new tractors after 31 December 2024
Browse 53 other sections — procedural / definitional / commencement
uri:annex/i/division/2
uri:annex/ii/appendix/1/division/1/division/1/division/1.1
uri:annex/ii/appendix/1/division/1/division/3/division/3.1/division/3.1.5.1
uri:annex/ii/appendix/1/division/1/division/3/division/3.1/division/3.1.5.5.4.1
uri:annex/ii/appendix/1/division/1/division/4
uri:annex/ii/appendix/1/division/1/division/6
uri:annex/ii/division/3
uri:annex/iii/division/2
uri:annex/iv/division/a/division/1/division/1.1
uri:annex/iv/division/a/division/1/division/1.3
uri:annex/iv/division/a/division/2/division/2.4
uri:annex/iv/division/b/division/1/division/1.1
uri:annex/iv/division/b/division/1/division/1.3
uri:annex/iv/division/c/division/1/division/1.2
uri:annex/iv/division/c/division/1/division/1.3
uri:annex/iv/division/c/division/2/division/2.2
uri:annex/ix/division/5/division/5.1
uri:annex/ix/division/5/division/5.2/division/5.2.1
uri:annex/ix/division/5/division/5.2/division/5.2.2
uri:annex/ix/division/5/division/5.2/division/5.2.3
uri:annex/ix/division/5/division/5.3/division/5.3.7
uri:annex/ix/division/5/division/5.3/division/5.3.9
uri:annex/ix/division/6/division/6.5
uri:annex/v/division/3
uri:annex/vi/division/2
uri:annex/vii/appendix/1/division/1/division/3/division/3.6/division/3.6.3
uri:annex/vii/appendix/1/division/1/division/3/division/3.7/division/3.7.3
uri:annex/vii/appendix/1/division/1/division/3/division/3.8
uri:annex/viii/division/3
uri:annex/xi/division/4
uri:annex/xi/division/5/division/5.2
uri:annex/xi/division/6/division/6.2
uri:annex/xi/division/6/division/6.3
uri:annex/xii/appendix/2/division/1/division/2/division/2.2/division/2.2.1
uri:annex/xii/division/2
uri:annex/xiii/division/3
Subject matter
Definitions
Requirements applying to construction and fitting of braking devices and trailer braking couplings
Requirements applying to testing and performance of braking systems and trailer braking couplings and of vehicles fitted with them
Requirements applying to the measurement of the response time
Requirements applying to energy sources and energy storage devices of braking systems and trailer braking couplings and to vehicles fitted with them
Requirements applying to spring brakes and to vehicles fitted with them
Requirements applying to parking braking systems equipped with a mechanical brake-cylinder locking device
Alternative test requirements for vehicles for which Type-I, Type-II or Type-III tests are not mandatory
Requirements applying to the testing of inertia braking systems, braking devices and trailer braking couplings and of vehicles fitted with them as regards braking
Requirements applying to vehicles with hydrostatic drive and their braking devices and braking systems
Requirements applying to the safety aspects of complex electronic vehicle control systems
Requirements and test procedures applying to anti-lock braking systems and to vehicles fitted with them
Requirements applying to EBS of vehicles with compressed-air braking systems or of vehicles with data communication via pin 6 and 7 of ISO 7638 connector and to vehicles fitted with such EBS
Type-approval of vehicles, systems, components and separate technical units
National type-approval of vehicles, systems, components and separate technical units
Entry into force and application
Explore more
Browse legislation
Find other UK business legislation with related guidance.